2009 FURUKAWA HCR1200
Price:USD $174,246
Buy
2009 FURUKAWA HCR1200
Used and New
Description:
Furukawa
HCR 1200
Year 2009
Current hours 5965
Hammer was re-bearing and resealed at 5637 hours
5776 hours, $57,391.51 work order was performed
1) Service machine:
- Service eng
- Oil samples
- Change final drive oils
- Change compressor filters
2) repair and tidy wiring on machine:
- install and wire in rear lights
- engine temp sender
- a/c clutch wiring repairs
- repair pre heater
- re-wire alternator wiring
- repair turbo boost sensor
- repair ground for fuel guage
3) Repair broken Console
4) Misc body work
- repair hood and bolt down
- repair bent steps
- repair bent rear guard
- remove rear doors, weld/paint/fix door frame/install doors
- repair boom support on hood
- repaired broken mirror
5) Re & Re wiper motor, replace with new
6) Replace stereo
7) Repair window latch and adjust door handle
8) Blow out heater and repair defrost switch
9) Clean heater AC system, recharge
10) Replace broken/cracked window
11) Trouble shoot and repair engine oil leaks
12) Repaired engine intake heater
13) Take apart hose minder
14) Disassemble boom parts / inspect make parts list / repair
15) Disassemble and inspect front and rear clamps / repair
16) Trouble shoot and fix dust collector purge jet system
17) Replace rod swing cylinder bushings and pins
18) Replace boom lift cylinder
19) Replace rod changer carosol grease seals
20) Install new bushings on cylinder for till boom
21) Install new bearing and grease seals for wheels on hose rail
22) Changed front hose roller bearings
23) Feed chain bushings and bearing replaced
24) Hammer and hose minder wear plates and roller replaced
25) Boom pins and bushings replaced
26) Replace hoses wear needed
27) Replace dust collector hose
28) Jaws repaired from bent and worn condition – new pins installed
29) Repaired rod roller system
30) Replaced Digital X – Y boom angle reader.
HCR 1200
Year 2009
Current hours 5965
Hammer was re-bearing and resealed at 5637 hours
5776 hours, $57,391.51 work order was performed
1) Service machine:
- Service eng
- Oil samples
- Change final drive oils
- Change compressor filters
2) repair and tidy wiring on machine:
- install and wire in rear lights
- engine temp sender
- a/c clutch wiring repairs
- repair pre heater
- re-wire alternator wiring
- repair turbo boost sensor
- repair ground for fuel guage
3) Repair broken Console
4) Misc body work
- repair hood and bolt down
- repair bent steps
- repair bent rear guard
- remove rear doors, weld/paint/fix door frame/install doors
- repair boom support on hood
- repaired broken mirror
5) Re & Re wiper motor, replace with new
6) Replace stereo
7) Repair window latch and adjust door handle
8) Blow out heater and repair defrost switch
9) Clean heater AC system, recharge
10) Replace broken/cracked window
11) Trouble shoot and repair engine oil leaks
12) Repaired engine intake heater
13) Take apart hose minder
14) Disassemble boom parts / inspect make parts list / repair
15) Disassemble and inspect front and rear clamps / repair
16) Trouble shoot and fix dust collector purge jet system
17) Replace rod swing cylinder bushings and pins
18) Replace boom lift cylinder
19) Replace rod changer carosol grease seals
20) Install new bushings on cylinder for till boom
21) Install new bearing and grease seals for wheels on hose rail
22) Changed front hose roller bearings
23) Feed chain bushings and bearing replaced
24) Hammer and hose minder wear plates and roller replaced
25) Boom pins and bushings replaced
26) Replace hoses wear needed
27) Replace dust collector hose
28) Jaws repaired from bent and worn condition – new pins installed
29) Repaired rod roller system
30) Replaced Digital X – Y boom angle reader.
Information:
| Year | 2009 |
| Hours | 5,965 |
1