3336136LP KPI-JCI Heavy sale in Missouri

SERIES 33 36” X 136’ LP SUPER STACKER

MAIN CONVEYOR EQUIPPED AS FOLLOWS:
FRAME – truss with tampered tail section to achieve a loading height of approximately 5 ½’
UNDERCARRIAGE – Heavy duty v-type with twin cylinder raise and cylinder covers
10 HP electric / hydraulic power pack to operate lift cylinders, power travel drives and extendable conveyor travel;
Axle – gullwing axle assembly. Includes: walking beam travel axle with eight (8) 11-22.5 tires, four (4) 385/65D-19.5 radial travel tires, less cylinders. A stiff arm shall be provided in place of the fold down cylinders. King pin, air brakes, travel, brake and directional lights, mudflaps, hydraulic planetary power travel drives for two wheel drive, cam arm-style rear undercarriage to maintain constant wheel radius when raising and lowering conveyor; A center heavy duty tow eye is included for positioning within the pit
DRIVE ASSEMBLY – Head end, v-belt drive for 425 FPM belt speed
Capacity – 850 TPH of 100 pcf material
Motor – 30 HP electric, 1800 RPM, TEFC 3/60/460, with starter & wiring
Reducer – Class I, Dodge TA5215 shaft mount
Backstop – Internal type in reducer
PULLEYS
Head Pulley – 16” grooved rubber lagged, Dodge bearings
Tail Pulley – 14” steel wing, Dodge bearings
TAKE-UP – screw type
IDLERS - CEMA “B” 5” diameter, steel roll, sealed for life ball bearings
Load Area Idlers – 20 degree close spaced under receiving trough
Troughing Idlers – 35 degree on 4’ spacing
Return Idlers – flat rolls on 8’ spacing
RADIAL RECEIVING HOPPER – (Rock box style) 5’6” long with adjustable rubber flashing
ANCHOR PIVOT – Anchor pivot for radial travel
BELT – Grade 2, 2 ply, 220 PIW, 3/16” x 1/16” mechanical fasteners

EXTENDABLE CONVEYOR EQUIPPED AS FOLLOWS:
FRAME – truss with head section
EXTENDABLE CONVEYOR – extendable conveyor moves in and out with a cable and hydraulic winch system (winch located in main frame conveyor) to extend the conveyor to 136 feet
DRIVE ASSEMBLY – Head end, v-belt drive for 630 FPM belt speed
Capacity – 850 TPH of 100 pcf material
Motor – 25 HP electric, 1800 RPM, TEFC 3/60/460, with starter & wiring
Reducer – Class I, Dodge TA4207 shaft mount
Backstop – Internal type in reducer
PULLEYS
Head Pulley – 16” grooved rubber lagged, Dodge bearings
Tail Pulley – 14” steel wing, Dodge bearings


TAKE-UP – screw type
IDLERS - CEMA “B” 5” diameter, steel roll, sealed for life ball bearings
Troughing Idlers – 35 degree on 4’ spacing
Return Idlers – flat rolls on 8’ spacing
BELT – Grade 2, 2 ply, 220 PIW, 3/16” x 1/16” mechanical fasteners
ELECTRICAL - NEMA 4 enclosure with main disconnect mounted on the rear undercarriage member; all starters and wiring to motors; start/stop pushbuttons for main conveyor motor, extendable conveyor motor, hydraulic power pack motor; cord holders and supports for power cable; LESS power cable – 460 volt, 3 phase, 60 hertz power required.

MANUAL CONTROL SYSTEM - the following hydraulic functions are manually controlled by switches on the electrical panel: power radial travel; conveyor raise and lower; extend and retract the extendable conveyor section

PAINT – Two part urethane primer, two part urethane topcoat – Factory standard color(s).


OPTIONS:
Belt Cleaners (2) – Martin with tensioner
Manual landing jacks (pin lock design)
Additional hydraulic planetary power travel drives for 4WD

Wizard Touch Automated Control System - Includes touch screen PLC operation allows for either factory pre-set or operator in-put parameters to control the power travel, conveyor raise and lower and telescoping of the extendable conveyor, radial travel limit switches and rotation sensor are included

Material Flow Sensor –causes power travel to stop when material is not detected on belt
(recommended with the automation package)

Hydraulic fold-down cylinders & plumbing for the radial travel tires on the gullwing axle

Year

2012