2000VSI CANICA-JAQUES Heavy sale in North Dakota

SUPERIOR/CANICA 2000 VSI IMPACTOR PLANT EQUIPPED AS PER BELOW:

CARRIER CHASSIS:
- MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL STEEL BEAMS
- TANDEM AXLE WITH (8) 11 X 22.5 RADIAL TIRES
- COMPLETE AIR BRAKE SYSTEM
- MUD FLAPS ON REAR AXLE
- TRAVEL LIGHTS WITH BRAKE AND DIRECTIONAL SIGNALS
- FIFTH WHEEL HITCH
- CRANK DOWN LANDING GEAR
- (4) FIXED, STRUCTURAL STEEL CRIBBING LEGS
HOPPERS AND CHUTES:
- UNDER-CRUSHER GATHERING HOPPER CONSTRUCTED OF 3/8" AR400 STEEL
- DIRECTS MATERIAL ONTO THE REAR DISCHARGE CONVEYOR
- ADJUSTABLE RUBBER FLASHING FULL LENGTH OF HOPPER
48" X 36' REAR DISCHARGE CONVEYOR:
- STRUCTURAL STEEL CHANNEL MAIN FRAME
- CLASS 2 DRIVE - 20 HP MOTOR, V-BELT DRIVE, SHAFT MOUNT REDUCER
- CAPACITY 400 STPH OF 100 PCF MATERIAL, 8' LIFT
- BELT SPEED 200 FPM
- HEAD PULLEY 14" DIAMETER, CROWN FACE, 3/8" HERRINGBONE LAGGED DRUM
- TAIL PULLEY 12" DIAMETER CHEVRON WING PULLEY
- REXNORD BEARINGS
- MANUAL SCREW TAKE-UPS
- LOAD AREA IDLERS C5, 20 DEGREE TROUGH, SPACED 12"
- CARRY IDLERS C5, 20 DEGREE TROUGH, SPACED 3'
- RETURN IDLERS C5 FLAT STEEL ROLLS
- 3 PLY BELTING 3/16" X 1/16" 330 PIW
- VULCANIZED BELT SPLICE
- EXTERRA PRIMARY BELT CLEANER
- FULL LENGTH SKIRTING
- FLAT COVERS ENTIRE LENGTH
WALKWAY:
- 3/16" DIAMOND TREAD PLATE, TWO-RAIL HAND RAIL, TOE BOARD
- INSTALLED ON BOTH SIDES OF CRUSHER AND OBSERVATION PLATFORM
- ELEVATED PLATFORM TO OBSERVE CRUSHER FEED AREA
- (1) LADDER TO BE USED FOR ACCESS ON EITHER SIDE OF CHASSIS
- WALKWAY TO COVER ENTIRE FIFTH WHEEL SECTION WITH REMOVEABLE
RAILING
HYDRAULIC LIFT ONLY JACKS:
- (4) 5" X 16" HYDRAULIC CYLINDERS
- (4) MANUAL LEVER VALVES, (1) FOR EACH CYLINDER
- 12 VOLT HYDRAULIC PUMPING UNIT
TEREX/CANICA 2000 VSI IMPACT CRUSHER:
- 2000 HEAVY DUTY (HD) VSI SINGLE DRIVE WITH OPEN TABLE AND ANVILS - UP
TO 250 STPH FEED RATE AND UP TO 4" (100MM) FEED SIZE
- TECO 300 HP 1200 RPM 586/7UZ FRAME, WITH STAINLESS STEEL BREATHER
DRAINS INSTALLED FOR SHAFT DOWN OPERATION
- LARGE ROLLER BEARINGS
- ASTRALLOY MAIN SHAFT WITH NON GREASE FLYWHEEL SEAL
- CAST CHROME PEDESTAL PROTECTION
- CAST TUB AND LID LINERS
- MODULAR OIL LUBE SYSTEM
- PATENTED "HYDRALID" HYDRAULIC LID LIFTER
- EXTERNALLY ADJUSTABLE FEED TUBE SYSTEM
- FEED HOPPER WITH BANG BOARD
- ROCK LINED FEED HOPPER
- HEAVY-DUTY MOTOR MOUNTS WITH COVERS AND ADJUSTABLE TAKE-UPS
- VIBRATIONS SHUT-OFF SWITCH
- LID SAFETY SWITCH AND LID SAFETY FOOT
- BELT GUARDS
- HEAVY DUTY TABLE
- CAST LINED FLYWHEEL
- PATENTED VAULTED ANVIL RING WITH INDEXING ADJUSTMENT OR DROP-IN
STOB TYPE ANVIL RING
- DRIVE BELTS AND SHEAVES
- ROCK BOX CRUSHING CHAMBER
- INSPECTION DOOR WITH SAFETY LCOK
- AUXILIARY ELECTRICAL CONTROL CABINET WITH R.P.M GUAGE, VIBRATION
DETECTOR (WARNING LIGHT), HOUR METER, OPEN-LID CRUSHER SAFETY
CUT-OFF, 2 HP LUBE SYSTEM, OIL SYSTEM HEATER STARTER AND 15 HP SPARE
STARTER.
- SANDBLASTED CHASSIS RUST INHIBITOR PRIMER AND ONE FINISH COAT
PAINTED TEREX WHITE (RAL1013)
- GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS.
GUARDS MAY NOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO
HAVE GUARDING INSPECTED.
ELECTRICAL SWITCHGEAR FOR A CANICA 300 HP VSI, EQUIPPED AS PER BELOW:
- 60 X 60 HOFFMAN NEMA 12 RATED ENCLOSURE WITH 800 AMP LOCKABLE
OPERATOR
- 400 HP ALTIVAR 71 SERIES VFD WITH LINE REACTOR
- VFD MOUNTED TO CANICA SUPPLIED AUX ELECTRICAL CONTROL PANEL
WITH RPM GUAGE, VIBRATION DETECTOR (WARNING LIGHT), HOUR METER,
OPEN LID SAFETY CUT OFF, 2 HP LUBE STARTER, OIL SYSTEM HEATER
STARTER AND 15 HP SPARE STARTER (UNDER CRUSHER) WITH TERMINATION
POINTS FOR ALL SAFETY SHUTOFF SWITCHES
- (1) SIZE #2 FOR INTERLOCKED FEED CONVEYOR, AND (3) SPARE 20 HP
- LEG KIT, SAFETY START UP HORN
- BUTTONS IN DOOR, E-STOP, AMP METER, VOLT METER, HZ METER, SPEED POT
- 900 CFM AIR TO AIR EXCHANGER WITH WEATHER COVER
- 5 KVA TRANSFORMER WITH 120V 20A SERVICE OUTLET
- SG SETS OF PLANT 30' FOR OPERATION
- 100' OF POWER CORD

Year	2016
Location	Fargo, North Dakota
Stock Number	E00048798
Serial Number	934977

SUPERIOR/CANICA 2000 VSI IMPACTOR PLANT EQUIPPED AS PER BELOW:

CARRIER CHASSIS:
- MAIN FRAME CONSTRUCTED OF WIDE FLANGE STRUCTURAL STEEL BEAMS
- TANDEM AXLE WITH (8) 11 X 22.5 RADIAL TIRES
- COMPLETE AIR BRAKE SYSTEM
- MUD FLAPS ON REAR AXLE
- TRAVEL LIGHTS WITH BRAKE AND DIRECTIONAL SIGNALS
- FIFTH WHEEL HITCH
- CRANK DOWN LANDING GEAR
- (4) FIXED, STRUCTURAL STEEL CRIBBING LEGS
HOPPERS AND CHUTES:
- UNDER-CRUSHER GATHERING HOPPER CONSTRUCTED OF 3/8" AR400 STEEL
- DIRECTS MATERIAL ONTO THE REAR DISCHARGE CONVEYOR
- ADJUSTABLE RUBBER FLASHING FULL LENGTH OF HOPPER
48" X 36' REAR DISCHARGE CONVEYOR:
- STRUCTURAL STEEL CHANNEL MAIN FRAME
- CLASS 2 DRIVE - 20 HP MOTOR, V-BELT DRIVE, SHAFT MOUNT REDUCER
- CAPACITY400 STPH OF 100 PCF MATERIAL, 8' LIFT
- BELT SPEED 200 FPM
- HEAD PULLEY 14" DIAMETER, CROWN FACE, 3/8" HERRINGBONE LAGGED DRUM
- TAIL PULLEY 12" DIAMETER CHEVRON WING PULLEY
- REXNORD BEARINGS
- MANUAL SCREW TAKE-UPS
- LOAD AREA IDLERS C5, 20 DEGREE TROUGH, SPACED 12"
- CARRY IDLERS C5, 20 DEGREE TROUGH, SPACED 3'
- RETURN IDLERS C5 FLAT STEEL ROLLS
- 3 PLY BELTING 3/16" X 1/16" 330 PIW
- VULCANIZED BELT SPLICE
- EXTERRA PRIMARY BELT CLEANER
- FULL LENGTH SKIRTING
- FLAT COVERS ENTIRE LENGTH
WALKWAY:
- 3/16" DIAMOND TREAD PLATE, TWO-RAIL HAND RAIL, TOE BOARD
- INSTALLED ON BOTH SIDES OF CRUSHER AND OBSERVATION PLATFORM
- ELEVATED PLATFORM TO OBSERVE CRUSHER FEED AREA
- (1) LADDER TO BE USED FOR ACCESS ON EITHER SIDE OF CHASSIS
- WALKWAY TO COVER ENTIRE FIFTH WHEEL SECTION WITH REMOVEABLE
RAILING
HYDRAULIC LIFT ONLY JACKS:
- (4) 5" X 16" HYDRAULIC CYLINDERS
- (4) MANUAL LEVER VALVES, (1) FOR EACH CYLINDER
- 12 VOLT HYDRAULIC PUMPING UNIT
- CANICA MODEL 2000 VERTICAL SHAFT IMPACTOR WITH ROS (ROCK ON STEEL)
SINGLE 300 HP DRIVE WITH HEAVY DUTY ENCLOSED ROTOR AND ANVIL RING,
UP TO 300 TPH AND 2.5 FEED SIZE:
- LARGE ROLLER BEARINGS (HIGHEST LOAD CAPACITY IN THE INDUSTRY)
- ASTRALLOY MAIN SHAFT WITH NON GREASE FLYWHEEL SEAL.
- CAST CHROME PEDESTAL PROTECTION
- CAST TUB AND LID LINERS
- MODULAR OIL LUBE SYSTEM
- PATENTED "HYDRALID" HYDRAULIC LID LIFTER.
- EXTERNALLY ADJUSTABLE FEED TUBE SYSTEM.
- FEED HOPPER WITH BANG BOARD
- ROCK LINED FEED HOPPER
- HEAVY-DUTY MOTOR MOUNTS WITH COVERS AND ADJUSTABLE TAKE-UPS
- VIBRATIONS SHUT-OFF SWITCH
- LID SAFETY SWITCH AND LID SAFETY FOOT.
- BELT GUARDS
- CAST LINED FLYWHEEL
- PATENTED VAULTED ANVIL RING WITH INDEXING ADJUSTMENT OR DROP-IN
STOB TYPE ANVIL RING
- DRIVE BELTS AND SHEAVES
- ROCK BOX CRUSHING CHAMBER
- INSPECTION DOOR WITH SAFETY LOCK
- AUXILIARY ELECTRICAL CONTROL CABINET WITH R.P.M. GAUGE, VIBRATION
DETECTOR (WARNING LIGHT), HOUR METER, OPEN-LID CRUSHER SAFETY CUT-
OFF, 2 HP LUBE SYSTEM STARTER, OIL SYSTEM HEATER STARTER AND 15 HP
SPARESTARTER. CONTAINS TERMINATION POINTS FOR ALL SAFETY SHUT-
OFF SWITCHES.
- ONE TECO 300 HP 1200 RPM TEFC, 586/7UZFRAME, SIDE LOAD, VERTICAL
MOUNT, CRUSHER DUTY MOTOR.
- SANDBLASTED CHASSIS RUST INHIBITOR PRIMER AND ONE FINISH COAT
PAINTED TEREX WHITE (RAL1013)
- GUARDING: FOR DRIVE AND TAIL PULLEYS, V-BELT DRIVE AND RETURN IDLERS.
GUARDS MAYNOT MEET ALL LOCAL CODES; CUSTOMER IS RESPONSIBLE TO
HAVE GUARDING INSPECTED.
ELECTRICAL SWITCHGEAR FOR A CANICA 300 HP VSI, EQUIPPED AS PER BELOW:
- 60 X 60 HOFFMAN NEMA 12 RATED ENCLOSURE WITH 800 AMP LOCKABLE
OPERATOR
- 400 HP ALTIVAR 71 SERIES VFD WITH LINE REACTOR
- VFD MOUNTED TO CANICA SUPPLIED AUX ELECTRICAL CONTROL PANEL
WITH RPM GUAGE, VIBRATION DETECTOR (WARNING LIGHT), HOUR METER,
OPEN LID SAFETY CUT OFF, 2 HP LUBE STARTER, OIL SYSTEM HEATER
STARTER AND15 HP SPARE STARTER (UNDER CRUSHER) WITH TERMINATION
POINTS FOR ALL SAFETY SHUTOFF SWITCHES
- (1) SIZE #2 FOR INTERLOCKED FEED CONVEYOR, AND (3) SPARE 20 HP
- LEG KIT, SAFETY START UP HORN
- BUTTONS IN DOOR, E-STOP, AMP METER, VOLT METER, HZ METER, SPEED POT
- 900 CFM AIR TO AIR EXCHANGER WITH WEATHER COVER
- 5 KVA TRANSFORMER WITH 120V 20A SERVICE OUTLET
- SG SETS OF PLANT 30' FOR OPERATION
- 100' OF POWER CORD

Year	2015
Location	Fargo, North Dakota
Stock Number	E00046675
Serial Number	793940