2016 INERTIA 5066 TRACKER
Price:USD $450,000
Buy
2016 INERTIA 5066 TRACKER
Used and New
Description:
CHASSIS
The chassis is constructed with W21 x 62 pound I-beam main frame rails. It has a heavy duty impactor
mount with both weld in and bolt on wear liners. The chassis also has an integrated grizzly bypass chute
to allow finer material to fall through the grizzly section of the feeder and on to the discharge belt. The
plant has two hydraulic drive tracks controlled by either remote or tethered. The tracks are bolt on and
there for removable if necessary. The plant comes equipped with king pin and a heavy duty removable
triple axle suspension with 11 x 22.5 tires, air brakes, lights, and mud flaps.
FEEDER
The feeder is an Inertia 60” x 18’ vibrating grizzly consisting of heavy channel and plate construction. It
has ½” weld in floor and side liners and a 4’ long grizzly bar section with 5” nominal spacing. The feeder
uses two Invicta BL 60-90 vibrating motors along with a slight decline in angle to feed the impactor.
HOPPER
The hopper is removable and is 9’ wide x 19’ long, 14 cubic yards non-heaping. It is constructed of 5/8”
plate and has a heavy-duty bolt on chain curtain to prevent material blow back from impactor.
IMPACTOR
The impactor is an Inertia 5066 HSI (50” diameter x 65” wide) single rotor impact crusher with
sectionalized frame construction of both welded and bolted heavy plate steel. It has replaceable frame
liners of HARDOX-400 material with a wear resistant steel rotor and cast replaceable blow bars. The
impactor has two adjustable breaker plates lined with HARDOX-400 material to control product
graduation and a spring relief system for non-crushable material. It incorporates self-aligning spherical
roller bearings and 4 bolt, split pillow blocks which are protected from dust contamination via a nonrupturable
labyrinth seal. It has four access doors for internal observation, inspection, maintenance, and
repair, and two hydraulic cylinders for opening the impactor hood.
REAR DISCHARGE CONVEYOR
The rear discharge conveyor is 42” x 39’ under crusher mounted. It has 4’ impact slide bed and CEMA “B”
five inch idlers. The tail pulley is a 12” wing pulley with 2 15/16” pillow block bearings. The head pulley is
a 16” crowned drum motorized pulley with vulcanized rubber lagging and interior bearings with pillow
blocks bolted to 18” telescoping take-ups. The conveyor belt is a heavy-duty rip stop belt with a flexco belt
splice.
POWER/DRIVE
The plant is powered by a 400hp Diesel engine that belt drives the impactor and 125kw 480V-113 amp
generator with 8V belts via a hydraulic engaging clutch. The generator supplies power to an on-board
electrical switch gear with 100 amp disconnect and circuit breakers. The circuit breakers are used to
supply power to the (2) Invicta vibrating motors on the feeder and the conveyor motor, with and additional
circuit breaker to supply power to an off-board piece of equipment. The belt drive has a fully enclosed
guard with two service doors.
The chassis is constructed with W21 x 62 pound I-beam main frame rails. It has a heavy duty impactor
mount with both weld in and bolt on wear liners. The chassis also has an integrated grizzly bypass chute
to allow finer material to fall through the grizzly section of the feeder and on to the discharge belt. The
plant has two hydraulic drive tracks controlled by either remote or tethered. The tracks are bolt on and
there for removable if necessary. The plant comes equipped with king pin and a heavy duty removable
triple axle suspension with 11 x 22.5 tires, air brakes, lights, and mud flaps.
FEEDER
The feeder is an Inertia 60” x 18’ vibrating grizzly consisting of heavy channel and plate construction. It
has ½” weld in floor and side liners and a 4’ long grizzly bar section with 5” nominal spacing. The feeder
uses two Invicta BL 60-90 vibrating motors along with a slight decline in angle to feed the impactor.
HOPPER
The hopper is removable and is 9’ wide x 19’ long, 14 cubic yards non-heaping. It is constructed of 5/8”
plate and has a heavy-duty bolt on chain curtain to prevent material blow back from impactor.
IMPACTOR
The impactor is an Inertia 5066 HSI (50” diameter x 65” wide) single rotor impact crusher with
sectionalized frame construction of both welded and bolted heavy plate steel. It has replaceable frame
liners of HARDOX-400 material with a wear resistant steel rotor and cast replaceable blow bars. The
impactor has two adjustable breaker plates lined with HARDOX-400 material to control product
graduation and a spring relief system for non-crushable material. It incorporates self-aligning spherical
roller bearings and 4 bolt, split pillow blocks which are protected from dust contamination via a nonrupturable
labyrinth seal. It has four access doors for internal observation, inspection, maintenance, and
repair, and two hydraulic cylinders for opening the impactor hood.
REAR DISCHARGE CONVEYOR
The rear discharge conveyor is 42” x 39’ under crusher mounted. It has 4’ impact slide bed and CEMA “B”
five inch idlers. The tail pulley is a 12” wing pulley with 2 15/16” pillow block bearings. The head pulley is
a 16” crowned drum motorized pulley with vulcanized rubber lagging and interior bearings with pillow
blocks bolted to 18” telescoping take-ups. The conveyor belt is a heavy-duty rip stop belt with a flexco belt
splice.
POWER/DRIVE
The plant is powered by a 400hp Diesel engine that belt drives the impactor and 125kw 480V-113 amp
generator with 8V belts via a hydraulic engaging clutch. The generator supplies power to an on-board
electrical switch gear with 100 amp disconnect and circuit breakers. The circuit breakers are used to
supply power to the (2) Invicta vibrating motors on the feeder and the conveyor motor, with and additional
circuit breaker to supply power to an off-board piece of equipment. The belt drive has a fully enclosed
guard with two service doors.
Information:
| Year | 2016 |
2016 INERTIA 5066 TRACKER
[744737]
2016 INERTIA 5066 TRACKER
Hard Rock Equipment & Rental LLC
Freeport, Illinois 61032
Freeport, Illinois 61032
1